TX10KSS PLUG-IN NEXT GENERATION
COD. TX10KSS/60D41/EPS
Puissance: 10.000W
10.000W PLUG-IN Next Gen System.
FEATURES
• Tunable over entire FM band (87.5 – 108 MHZ), without tuning.
• Overall efficiency better than 71-73%.
• Hot-pluggable and broadband power amplifier modules.
• High redundancy guaranteed.
• Each amplifier module provides Automatic Power Control.
• Each module has its own hot plug-in fans set.
• Suitable for mono & stereo broadcast operations.
• Protection against high VSWR, overdrive, overcurrent and overtemperature.
• Compliance to IEC safety standards.
• Compliance to ETSI – CCIR – FCC standards.
• Entire transmitter can be switched off through an emergency button.
• All measurement and working parameters are displayed on front panel.
• Remotely controllable by telemetry system.
• Design for 24/7 non-stop operation.
• The transmitter include an integrated system for automatic and manual switching between two exciters.
In Automatic mode the changeover is activated when active power of exciter falls below 3dB.
EPS:
• Each power supply “PS" can be removed or plugged without turning off the transmitter.
• The transmitter is capable of generating an output power with ample margin thanks to oversized power supplies.
• By installing an additional PS, the transmitter will operate at full power in the event of a single PS failure, eliminating the need for derating.
• Each PS features an automatic magnetic switch preventing short circuits and ensuring uninterrupted signal broadcasting.
• The power stream generated by these PS are distributed in parallel to all RF modules; consequently if one
power supply fails all RF modules maintain balanced operation.
• The transmitter’s CCU oversee continuously the operational status of each individual power supply.
• In the event of a failure the "ECM" electronic control module will optimize the transmitter efficiency.
• In an empty slot an additional power supply can be turned on so in the
event of a power supply failure there will be no reduction in power. It is a N+1 PLS system . Only from 4 to 10kW(option)
• Tunable over entire FM band (87.5 – 108 MHZ), without tuning.
• Overall efficiency better than 71-73%.
• Hot-pluggable and broadband power amplifier modules.
• High redundancy guaranteed.
• Each amplifier module provides Automatic Power Control.
• Each module has its own hot plug-in fans set.
• Suitable for mono & stereo broadcast operations.
• Protection against high VSWR, overdrive, overcurrent and overtemperature.
• Compliance to IEC safety standards.
• Compliance to ETSI – CCIR – FCC standards.
• Entire transmitter can be switched off through an emergency button.
• All measurement and working parameters are displayed on front panel.
• Remotely controllable by telemetry system.
• Design for 24/7 non-stop operation.
• The transmitter include an integrated system for automatic and manual switching between two exciters.
In Automatic mode the changeover is activated when active power of exciter falls below 3dB.
EPS:
• Each power supply “PS" can be removed or plugged without turning off the transmitter.
• The transmitter is capable of generating an output power with ample margin thanks to oversized power supplies.
• By installing an additional PS, the transmitter will operate at full power in the event of a single PS failure, eliminating the need for derating.
• Each PS features an automatic magnetic switch preventing short circuits and ensuring uninterrupted signal broadcasting.
• The power stream generated by these PS are distributed in parallel to all RF modules; consequently if one
power supply fails all RF modules maintain balanced operation.
• The transmitter’s CCU oversee continuously the operational status of each individual power supply.
• In the event of a failure the "ECM" electronic control module will optimize the transmitter efficiency.
• In an empty slot an additional power supply can be turned on so in the
event of a power supply failure there will be no reduction in power. It is a N+1 PLS system . Only from 4 to 10kW(option)
| TX10KSS/60D41/EPS | ||
| Parameter | Value | |
| GENERALS | ||
| RF Output Power | 10kW + 10% | |
| Frequency Range | 87,5 – 108 MHz | |
| Driver power for rated output | 30W | |
| VSWR | 1.4:1 with automatic fold-back at higher VSWR | |
| Asynchronous AM S/N Ratio | Typically >70dB | |
| Synchronous AM S/N Ratio | Typically > 55dB | |
| Harmonics suppression and Spurious | Typically < 85dB | |
| RF Harmonics | Exceeds ETSI/CCIR/FCC requirements | |
| RF Spurious | Exceeds ETSI/CCIR/FCC requirements | |
| Environmental working conditions | -10 °C to + 50 °C / 95% relative Humidity non condensing | |
| POWER REQUIREMENTS | ||
| AC Power Input | AC Supply Voltage | 400V ±10% AC Three-Phase 3F+N |
| 230V ±10% AC Three-Phase 3F+N | ||
| 230V ±10% AC Mono-Phase 50/60 Hz | ||
| Active Power Consuption | about 14.1 kW | |
| Power factor | > 0.95 | |
| Overall Efficiency | 71/73 % | |
| Connector | Terminal Block Standard | |
| MECHANICAL DIMENSIONS | ||
| Phisical Dimensions | L x H x W |
40u: 685 mm x 1935 mm x 1000 mm 32u: 685 mm x 1620 mm x 1000 mm |
| Weight | about 360 kg | |
| Cooling | Forced, with internal fan | |
| Acoustic Noise | < 75 dBA | |
| OUTPUTS | ||
| RF Output | 50 Ohm (1+5/8" EIA flange type) |